Jay Martin
Moderator
Registered: 04-2010
Posts: 164
|
Reply | Quote
|
|
Re: crazy...jay martin propellers......just crazy
Carry what you need, not everything you own, I see so many guys looking for that extra mph that has Bass pro shop in every compartment... ...
---
www.jaymartinpropellers.com
|
Jul/18/2010, 9:12 pm
|
Link to this post
Email Jay Martin
PM Jay Martin
|
wevel2
Moderator
Registered: 04-2010
Posts: 352
|
Reply | Quote
|
|
Re: crazy...jay martin propellers......just crazy
ive cranked the jack plate another half inch thatl put me at 2 5/8 under pad water pressure i dont think will be a issue i think ill lose lift before i lose psi but well see when im loaded to the gills a slight roooster tail no more than a few inches high appears... so ill keep cranking to get some more rpms till i lose prop bite or psi ... the plat is maxed out so if it keeps bitin looks like ill have to go up a set of holes. ill post back speed when i get to run here im looking for those last mph tourny loaded im thinking mid 50s
--- its almost done..wait... awl he!!..it will never be done
|
Jul/18/2010, 10:07 pm
|
Link to this post
Email wevel2
PM wevel2
|
bonsaibp
Administrator
Registered: 04-2010
Posts: 947
|
Reply | Quote
|
|
Re: crazy...jay martin propellers......just crazy
Sounds like another awesome job by Jay Martin Propellers!
--- bonsaibp
I AM NOT SAYING THERE SHOULD BE CAPITAL PUNISHMENT FOR STUPIDITY,
BUT, WHY DON'T WE JUST TAKE THE SAFETY LABELS OFF OF EVERYTHING
AND LET THE PROBLEM SOLVE ITSELF?"
blkdog812
|
Jul/21/2010, 9:54 am
|
Link to this post
Email bonsaibp
PM bonsaibp
|
wevel2
Moderator
Registered: 04-2010
Posts: 352
|
Reply | Quote
|
|
Re: crazy...jay martin propellers......just crazy
i went another half prop still biting water the same stering torque is bad and the stern likees to go right when i want to go left kind paddle wheeling without hydraulic stering looks like im going to have to drop her a quarter or half to get my sterrring back i never thought stering would be the limiting factor in jack plate hieght but i guess it is ....
--- its almost done..wait... awl he!!..it will never be done
|
Jul/30/2010, 5:57 pm
|
Link to this post
Email wevel2
PM wevel2
|
Jay Martin
Moderator
Registered: 04-2010
Posts: 164
|
Reply | Quote
|
|
Re: crazy...jay martin propellers......just crazy
Do you have a torque tab on the skeg?
If not here is about the best deal on one that you will find.
http://cgi.ebay.com/ebaymotors/TH-Marine-Torque-tab-TAB-1-bass-boat-skeg-new-_W0QQcmdZViewItemQQhashZitem20aed8090cQQitemZ140372347148QQptZBoatQ5fPartsQ5fAccessoriesQ5fGear
Last edited by Jay Martin, Jul/30/2010, 6:16 pm
---
www.jaymartinpropellers.com
|
Jul/30/2010, 6:14 pm
|
Link to this post
Email Jay Martin
PM Jay Martin
|
wevel2
Moderator
Registered: 04-2010
Posts: 352
|
Reply | Quote
|
|
Re: crazy...jay martin propellers......just crazy
nope dont have one ill do some research as to them.... when i drop the throtel a bit even if i trim down alot it will hook bad to the left it always did it worse with the three blade ... 4 blade wouldnt hardly do it but at these heights it doing it bad if i let a little bit without trimming down like hopping little wakes it will dart will these help this to or is this another problem all to gether i thought it may have been my load but i dropped the plate and went back out and none of the side afects occured ... im a preety big fellow and its all i want to controll it arms start burning after a couple miles....
--- its almost done..wait... awl he!!..it will never be done
|
Jul/30/2010, 6:56 pm
|
Link to this post
Email wevel2
PM wevel2
|
wevel2
Moderator
Registered: 04-2010
Posts: 352
|
Reply | Quote
|
|
Re: crazy...jay martin propellers......just crazy
hey jay or anybody that knows about torq tabs do i need to rivit it on or have it welded(i dont weld cast) id rather rivit it... will these things crack or break the skeg with all that force on them... thanks
--- its almost done..wait... awl he!!..it will never be done
|
Aug/1/2010, 9:13 pm
|
Link to this post
Email wevel2
PM wevel2
|
Jay Martin
Moderator
Registered: 04-2010
Posts: 164
|
Reply | Quote
|
|
Re: crazy...jay martin propellers......just crazy
Have it welded, rivits and screws don't hold worth a darn.
---
www.jaymartinpropellers.com
|
Aug/1/2010, 10:52 pm
|
Link to this post
Email Jay Martin
PM Jay Martin
|
wevel2
Moderator
Registered: 04-2010
Posts: 352
|
Reply | Quote
|
|
Re: crazy...jay martin propellers......just crazy
looks like ill be taking it to our nose cone guy titus for torq tab then .....
--- its almost done..wait... awl he!!..it will never be done
|
Aug/2/2010, 9:37 pm
|
Link to this post
Email wevel2
PM wevel2
|